EJA110A MANUAL PDF

Model EJAA, EJAA and. EJAA this manual thoroughly and fully understand how to operate This manual should be passed on to the end user. User’s manual • Read online or download PDF • Yokogawa EJAA User Manual. View and Download YOKOGAWA EJAA user manual online. EJA Series Differential Pressure and Pressure Transmitters. EJAA Transmitter pdf manual.

Author: Akizil Gardacage
Country: Nepal
Language: English (Spanish)
Genre: Sex
Published (Last): 19 November 2006
Pages: 131
PDF File Size: 6.30 Mb
ePub File Size: 9.74 Mb
ISBN: 335-6-15360-325-7
Downloads: 93147
Price: Free* [*Free Regsitration Required]
Uploader: Zulmaran

Follow the procedure below to change the unit.

User’s Manual Model EJAA, EJAA and EJAA Differential |

The recommended height between the HP process connection and the transmitter is show in the following table. When a shrouding bolt is driven clockwise by an Allen wrench, it is going in and cover lock is released, and then the cover can be opened.

Therefore, if you switch off the transmitter within two hours from when the error occurs, there is no history of that error stored in the transmitter, and this function is meaningless. UNIT Follow the procedure below jea110a change the static pressure units. This subsection describes the procedures for cleaning and replacing the capsule assembly.

Areas where self-diagnostic offers support 9.

Inhibiting zero adjustment by the 0 P1 F Doing so completes the LRV setting. Either of these terminals may be used.

Model ejaa | Yokogawa EJAA User Manual | Page 69 / 83 | Original mode

Setting User-set Engineering Unit c. Reverse mode is used for applications in which safety requires that output be driven toward 20 mA if input is lost. Unless otherwise specified by order. Ignore the polarity since the BT is e It is recommended that crimp-on solderless terminal AC-coupled to the lugs for 4 mm screws with insulating sleeves be BT terminal box. Such a manifold makes it easier to disconnect the transmitter from the impulse piping, and is convenient when adjusting the transmitter zero point.

TOP Related Articles  MAISEY YATES AN ACCIDENTAL BIRTHRIGHT PDF

Flexible metal conduit DC power is required for the transmitter loop. An integral indicator can be installed in the following three directions. If the transmitter must be installed in a See Figure 6. Use this function only where there is no alternative. You must do this in order to avoid overloading the transmitter from either the high or the low pressure side when beginning operation.

YES Adjust the output. Then, remove and remount them on the opposite side.

Normally, only non-conductive pollution occurs. Differential pressure transmitters, which serve as the core of field instrumentation, are widely used to jea110a the flow rate, pressure and density of liquids, gases and steam, as well as the level of liquid in a tank. Changing this parameter changes the unit for the A Model pressure regulator pressure pump Pressure range: EPS correction value by adding 4.

Yokogawa EJA110A User Manual

Mounting the Diaphragm Seals Pressure Accessory – Vessel, Type of Fluid: Note 1 8 Turn the external zero-adjustment screw in the desired direction. LCD contrast setting 5. Horizontal impulse piping type, right side high pressure Pressure Accessory – Vessel Type of Fluid: It may also be used to alert against permission. Tag plate for type n protection 5 Maintenance and Repair Tag plate for flameproof, intrinsically safe type, type n protection, and Dust WARNING The instrument modification or parts replacement by other than authorized Representative of Yokogawa Electric Corporation is prohibited and will void the certification.

TOP Related Articles  CHRONICLES OF ATHAS PDF

EJA110A Differential Pressure Transmitter (DISCONTINUED)

Read carefully before using the transmitter. Follow the procedure below to change this setting. Output status at CPU failure and hardware error; Up-scale: EPS terized according to the specification. Indicates that operating the hardware or software in this manner may ea110a it or lead to system failure. Procedure is shown in the figure below.

Sets the calibration range for 4 to 20 mA DC.

Any diagrams, data and other information you can include in your communication will also be helpful. C2 Failure alarm up-scale: In this sequence, the history of the most F Note the following points when referring to these piping examples. Note 1 4 Turn the external zero-adjustment screw in the desired direction. DC power is required for the transmitter loop. Differential pressure and pressure transmitters 66 pages.

Measurement system problem Isolate problem in measurement system.